A two-component, 100% solids, high-performance self leveling floor coating specifically designed to provide an extremely hard wearing, durable, high gloss, seamless, hygienic surface.

• Zero VOC, very low odor
• High chemical resistancen
• Available as an anti-slip finish

Technical Data Sheets • MSDS Information

A three-component, 100% solids, high build self leveling floor coating designed for applications requiring film builds greater than 30 mils DFT. It is intended as a cost-effective, high build system with most of the physical characteristics of the standard IMPAX 650 SL.

• Full gloss
• High film build in one coat
• Economical for high film thickness applications

Technical Data Sheets • MSDS Information

A two-component, 100% solids, high-performance, self leveling floor coating designed to cure rapidly for fast recoat or minimal downtime, while maintaining most of the physical properties of the standard IMPAX 650 SL.

• Zero VOC, very low odor
• Accelerated curing reduces downtime
• Anti-slip texture available

Technical Data Sheets • MSDS Information

An interior/exterior, high solids, polyester aliphatic urethane floor coating for marine and industrial applications. Its high gloss finish is abrasion, stain, chalk and chemical resistant.

• Easily applied by brush, roll or spray
• High abrasion and stain resistance
• Anti-slip finish available

Technical Data Sheets • MSDS Information

A seamless, decorative, broadcast type system that incorporates clear, 100% solids technology in conjunction with multi-colored quartz aggregates. The low odor, zero VOC system offers an anti-slip or smooth finish and integral cove base capabilities.

• High film build, nominal thickness 1/8"
• Zero VOC, low odor system
• Colors limited only by the imagination

Technical Data Sheets • MSDS Information

A decorative coating system for commercial, industrial and architectural applications integrating high solids IMPAX technology with multi-colored vinyl flakes. Attractive and easy to install, the low odor, low VOC formulation is economical.

• Simple, economical installation
• Attractive, multi-colored finishes
• Available in smooth or lightly textured finishes

Technical Data Sheets • MSDS Information

A trowel-applied epoxy surfacing and leveling system for new or old floors where extreme physical properties are required. The fast curing, high build finish is durable, anti-slip and reduces downtime.

• Higher physical properties than concrete
• Durable, anti-slip finish
• Convenient kit sizes

Technical Data Sheets • MSDS Information

An epoxy surfacing and leveling system designed for application by screed box and power trowel. The high build finish is durable and has very high physical properties.

• High production 1/4" system
• Integral cove base capabilities
• Prepackaged in convenient kits

Technical Data Sheets • MSDS Information

Impax PGE is a versatile, two-component, 100% solids epoxy coating system designed for use with selected aggregates to produce a durable, high-build, monolithic surface. When applied over mechanically prepared substrates, it is self-priming and can be topcoated with many of the Impax topcoats to provide a wide range of textures, colors and finishes. Impax PGE is easily applied using standard notched trowels, squeegees or gauge rakes, and can provide film thicknesses up to 1/8" in a single application.

• Economical high-build epoxy slurry
• Self-priming
• Convenient bulk packaging
• Enhanced impact and thermal resistance

Technical Data Sheets • MSDS Information

A trowel-applied, acid resistant, novolac epoxy resurfacing and leveling system for protecting concrete, wood and steel in many corrosive environments. The high build finish is durable, anti-slip and cures quickly to reduce downtime.

• Resists 98% sulfuric acid
• Fast cure reduces downtime
• Durable, anti-slip finish

Technical Data Sheets • MSDS Information

A thin film, two-component, clear water based epoxy primer/sealer designed for use with most high performance floor coatings.

• Low viscosity for maximum penetration
• Effective barrier coat over many existing finishes*
• Easy to use brush, roll or spray application
• Convenient recoat properties
• Excellent for use over acid-etched concrete

*test patch must be performed

Technical Data Sheets • MSDS Information

A clear, high solids, high build, low viscosity primer designed for use with clear finish coats or any of the DecoBlend™ systems. The penetrating primer’s formulation is fast curing, low odor, VOC compliant and reduces bubbling and pinholing that occur when coating porous substrates.

• High build for mechanically prepared substrates
• Quick cure allows fast recoat
• Low odor, VOC compliant

Technical Data Sheets • MSDS Information

A ITW RUST INHIBITIVE 7CZ PRIMER is a lead and chromate free, rust inhibitive, two-component, epoxy primer specifically designed for use in conjunction with ITW Polymer Technologies coatings applied to metal substrates. It meets USDA standards for maintenance protective coatings not in direct contact with food in federally inspected meat and poultry plants.

• Recommended for use as a metal primer in severe
  industrial and chemical environments.
• Excellent adhesion to properly prepared iron and steel surfaces, providing rust resistance to ferrous substrates, both on initial application and in the event of damage to the topcoat.
• Can be used under many epoxy, urethane, vinyl, chlorinated rubber and coal tar/epoxy finish coats.

Technical Data Sheets • MSDS Information

A low viscosity, 100% solids, high build, penetrating epoxy primer designed to be used as a moisture blocking primer where vapor transmission is a concern.

• High build for mechanically prepared substrates
• 100% solids, solvent free
• Recommended when vapor transmission is a concern

Technical Data Sheets • MSDS Information

An interior, two-component polymer hybrid, designed to provide a resilient filler for expansion joints. It’s chemistry provides excellent flexural strength and elongation, while maintaining impressive tensile strength.

• 100% Solids, solvent-free product
• Excellent adhesive strength and flexibility
• Pourable grade, superior workability
• Easily mixed with drill and mixing blade
• High chemical resistance

Technical Data Sheets • MSDS Information

A two-component epoxy paste developed specifically for sealing, smoothing and fairing applications on concrete, metals, wood or masonry.

• 100% solids, solvent free product
• Excellent non-sagging properties for horizontal or vertical applications
• Smooth consistency for easy application
• Long pot life
• Easily mechanically sanded or ground

Technical Data Sheets • MSDS Information

An easily mixed, two-component epoxy paste developed for maximum productivity when filling in bug holes, anchor bolt holes, and pinholes. It can also be used as a skim coat for mildly spalled areas. It is specifically used for sealing, smoothing and fairing applications on concrete, metals, plastics (FRP), wood or masonry.

• Easily mixed with a drill and mixing blade
• 100% solids, solvent-free product
• Excellent workability
• Creamy paste consistency
• Natural unpigmented color

Technical Data Sheets • MSDS Information

A 100% solids, two-component, equal volume epoxy system used as an adhesive to join concrete to concrete, masonry, tiles or dissimilar materials. The non-shrinking mortar/grout is used as filler for concrete, brick or block structures and as cove and seal at the juncture of floors and walls.

• Easy to mix and apply
• USDA approved and OSHA compliant
• Non-sagging for vertical or overhead surfaces

Technical Data Sheets • MSDS Information